PIETTA 1860 ARMY PERCUSSION OR CARTRIDGE REVOLVER GRIPS ; 2P IVORY SCROLL ENGR.

Arizona Custom Grips

Pietta

1860 Army

These grips are for
the Pietta Cap & Ball and Cartridge
Revolvers with the 3-1/2” tall 1860 Army sized gripframe.

~see below for details~

~ Exclusive ~

  MAGNA-TUSK™ 

white ivory GRIPS

Scrollwork engraved

Milled out of a solid block of
Magna-Tusk™, denser and heavier than regular Ivory or Stag.  See below for details.

~~~~~

two-PIECE
(with SCREWHOLE) STYLE grips

THIS LISTING IS FOR OUR
TWO-PIECE (SCREWHOLE) STYLE GRIPS

********

ONE-PIECE VS. TWO-PIECE STYLE GRIPS EXPLAINED:

Note: One-Piece style grips do not use a screw
but instead use an internal spacer. 
Two-Piece style grips incorporate a visible screw and screwhole,
allowing easy and quick removal for cleaning or maintenance of your
revolver.  We manufacture both
types.  Both styles of our grips will
interchange and work on either style of grip frame, no matter how your revolver
is currently set up.  Both styles are
traditional and historical designs and both were originally used on early
Colts, so whichever style you choose is really a matter of personal
preference. 

One-Piece style grips (i.e., grips
which do not have a visible screwhole in the grips) incorporate a user-installed
spacer between the grip panels, as seen on many of the early Colts.  The spacer (included with your grips) is sent
unmounted to ensure the optimum fit to your particular frame.  Installation is simple and takes only a few
minutes, and is explained in the included instructions.  This results in a rock-tight fit, without the
need of a screw.  One-Piece grips are preferred
by many collectors for their clean lines and traditional look. Once mounted,
they are taken on and off by removing the three backstrap screws, and pulling
the grip and backstrap backwards. 
Reinstallation is in reverse order. 

Alternatively, our Two-Piece style
grips (i.e., grips with a visible screw) offer the superior convenience of
quick grip removal.  In addition to the screw
our Two-Piece style grips include a free Conversion Kit, allowing their use on revolvers that are currently
set up for One-Piece style grips that do not have a grip pin (as is the case
with most Italian revolvers).  The
Conversion Kit replaces the need for a grip pin and is actually a stronger
design, and allows the grips to lock up tight on the frame, allowing no
movement.  This
requires no modification to your revolver and gives you the advantage of the
ease of maintenance of Two-Piece grips, while preserving the integrity of your
revolver in original factory condition. Two-Piece style grips were
used on many of the early Colts, and are a traditional and iconic historical
design, offering a distinctive look and convenience preferred by many shooters and
collectors.

Fully
illustrated, easy-to-follow instructions are included with every order. 

Rev
23120102

~~~~~

WHAT THESE WILL FIT:

(Note: Please read these
paragraphs thoroughly, including the “Will NOT Fit” section below):

These grips are
correctly milled and detailed to fit the following Pietta revolvers, which are
fitted with the 3-1/2” tall 1860 Army sized gripframe, which are imported and
marketed through Cimarron, Taylor’s & Company, EMF, Navy Arms, etc. 

Please note that these
will NOT
fit shorter (Navy sized) gripframes which measure around 3-1/16” to 3-1/8”
tall.  To make sure you are ordering the correct grip, please check
your grip frame measurement prior to ordering. 

WILL FIT THE FOLLOWING:

Pietta Blackpowder (Percussion) Revolvers with the
3-1/2” tall 1860 Army gripframe:

          * Pietta
1860 Army .44 Caliber Blackpowder (Cap & Ball Percussion) revolvers;

          * Pietta 1851
Navy Blackpowder Revolvers with the 3-1/2” tall 1860 Army sized gripframes.  These are usually chambered in
.44 Caliber and have a steel
gripframe.  Please
note that these will NOT fit the ‘51 Navys with the more common,
shorter Navy gripframes, which measure around 3-1/8” tall.  Your gripframe must be 3-1/2” tall for these
to work.

Pietta Cartridge Revolvers with the 3-1/2” tall 1860
Army gripframe:

* Traditions/Pietta Frontier .44 Magnum (and a few .357 Magnum Frontiers using the taller
3-1/2” 1860 Army grip frame);

* EMF/Pietta Great Western II Alchimista
I, II, or III.  *Please note that
these will NOT fit the other Great
Western IIs which use the shorter 3-1/8” gripframe;

* Cimarron/Pietta El Malo II with 3-1/2” Tall “plowhandle” style gripframe *(NOTE: these will NOT fit the El Malo II with the “Birdshead” style gripframe, which
is a completely different grip shape. 
They will also NOT FIT the El
Malo I which has the shorter 3-1/8” Navy sized frame). 

* Cimarron/Pietta Eliminator;

*Taylor’s & Co./Pietta TC9 revolvers with the 3-1/2” Tall gripframe.  (NOTE:
these grips will ONLY fit the TC9
with the 3-1/2” tall 1860 Army sized gripframe with Checkered Walnut grips.  These will NOT fit the TC9 with the shorter 3-1/8” tall gripframe with Black Checkered
Plastic grips;

* AND ALL other Pietta revolvers using the 3-1/2” tall 1860 Army sized grip
frame. 

Please contact us if you
have any questions, or cannot find the proper grip, and we will be happy to
help.

WILL NOT FIT: 

These grips are made to
fit ONLY Pietta revolvers,
and will NOT fit
anything made by Uberti, Armi San Marco, Colt, or any other manufacturer. 
If you have one of these other makes of revolvers and cannot find the grip you
need, please contact us and we will be happy to help.

Also, please note that
these will NOT fit the Bisley, the Birdshead, the
Thunderer, Thunderball, or the Lightning style revolvers, which incorporate a
completely different shaped gripframe than the grips shown in the pictures.

Custom fitting to your frame is also available.  Please contact us for more information.

Rev.
23120145