UBERTI SAA MAGNA-TUSK™ SINGLE ACTION ARMY WHITE STAG GRIPS ~ Cattleman, etc.

Arizona Custom Grips

UBERTI SAA

(SINGLE ACTION ARMY REVOLVERS)

~ Exclusive ~

  MAGNA-TUSK™

white STAG GRIPS

Simulated Stag Grips milled out of a solid block of
Magna-Tusk, denser and heavier than regular Ivory or Stag.  See below for details.

~~~~~

two-PIECE
(with SCREWHOLE) STYLE

THIS AUCTION IS FOR THE TWO-PIECE (SCREWHOLE) STYLE.

Note: ANY of
our grips, whether ONE-PIECE OR TWO PIECE style, will interchange and
work on either style of grip frame. 

We include, free of charge, a conversion kit
which allows these two-piece grips to mount onto a one-piece style grip frame
(without a grip pin).  Our conversion kit replaces the need for a
grip pin and is actually a stronger design, and locks the grips up tight
against the frame, allowing no movement. 
This
gives you the advantage of the ease of maintenance of two-piece grips, while
preserving the integrity of your revolver in original factory condition. 

Grip screw, conversion kit, and
full illustrated instructions are included with each set of grips. 

10292000

~~~~~

WHAT THESE WILL FIT 

(Please read this through in its
entirety, including the "what these will NOT fit section below):

These Grips WILL FIT: 

* ANY of the standard sized UBERTI 1873 Single Action Army
“plowhandle” style revolvers.  Uberti’s
standard sized grips will measure
somewhere between 3-1/16 – 3-1/8” tall, depending on how you hold your
ruler, tape, or caliper. 

These will be
marked “Uberti,” and may also (but not necessarily) be marked by the U.S. importer,
such as “Cimarron,” “Taylors & Co.”, “Navy Arms”, or “EMF”, etc. 

In addition to
fitting any of the standard UBERTI SAA style revolvers, these grips will fit (i.e.,
incorporate the additional milling and fitting) for any of the following Uberti
SAA revolvers:

* Cimarron / Uberti Cattleman,
1873 Cattleman
II, Cimarron Model P, Evil Roy, El Patron, Hombre*,
American Arms Regulator*, Cimarron New Sheriff, Uberti US 7^th Cavalry, U.S.V. Artillery, and Cavalry Scout, Pistoleer, Holy Smoker, Wyatt Earp Buntline, Rooster Shooter, Chisholm, Cody, Desperado, Frisco, Old West, Stallion, Buntline, Horseman, SASS Pro, CMS Pro, E.M.F. Dakota II*
or Dakota III*;

* Also:  Taylor’s & Co.  Smoke
Wagon, Cattleman, Gambler, Cattleman 12-Shot, Runnin’
Iron, Taylor Marshall, Drifter, Devil Anse, Old Randall*,
and Ranch Hand*;

* Also: Any
of Stoeger’s Uberti revolvers, or any Uberti SAA style revolver with the
standard sized grip frame, or Uberti revolver from any other importer, even
without a specific name or designation. 
If you have a standard SAA style revolver marked Uberti, these will fit.

*PLEASE NOTE: if you have a BRASS
gripframe (such as found on the Hombre,
the Regulator, the Dakota II or III, Old Randall, or Ranch Hand
revolvers), you MUST contact us
prior to ordering and let us know what you have, as these grips may require additional
specifications, profiling, and machining cuts. 

What these WILL NOT FIT: 

1.  Please note that these grips are made to fit ONLY the Uberti Model 1873 style Single Action revolvers, with the
typical “plowhandle” shaped gripframe, and will NOT fit other makes of revolvers (such as Pietta, Armi San
Marco, Colt, Ruger, etc.).  These grips will
also NOT fit the Bisley, the
Birdshead, the Thunderer or the Lightning style revolvers, from ANY maker, which
use a completely different shaped grip frame. 
Please email if you have any questions.

2.  In addition, these WILL NOT FIT grip frames which are around 3-3/8” tall.  To make sure you are ordering the correct
grip, please check your grip frame measurement prior to ordering.  Your grips
or grip frame should measure somewhere between 3-1/16 – 3-1/8” tall, depending on how you hold your ruler,
tape, or caliper.  The important thing is
to make sure they are NOT around 3-3/8” tall. 
Taylor & Co.’s Gunfighter, Taylor’s Cattleman
44 Mag., Cimarron Bad Boy, the El Patron Grizzly Paw, and the Uberti Callahan, for example, have the taller 3-3/8”
grip frame.   If you have one of these, any of our Uberti
1860 Army Conversion & Metallic Cartridge revolver grips are milled to work
for these, as well as the Conversions. 

Please send us an
email and tell us your specific model if you cannot locate what you need, or if
you have any questions.  We are always
happy to help.

A note on
the Italian-produced Revolvers:

The
Italian firms, located in Northern Italy, have been making SAA style revolvers
now for well over a half century, and have made a huge number of makes and
models and grip frame profiles with varying configurations over the years.  We have an in-depth knowledge of the
differing grip configurations, have a large library of gripframe variations
from the various makers both old and new, and have vast experience making grips
for Uberti, Pietta, Armi San Marco, and the other Italian gunmaking firms.   Our experienced makers go to great lengths
to ensure an exacting fit, including utilizing modern precision CNC production
techniques, as well as incorporating old-time hand tuning and hand checking the
fit of every grip on our reference frames prior to leaving our factory.  We have a long list of many satisfied
customers in the shooting industry who have purchased grips to use in a wide
variety of applications, and we can safely and confidently guarantee proper fit
and finish to your complete satisfaction.

For an
additional charge, custom fitting is an option. 
Please contact us for further details if you are interested in custom
fitting.

06222100

Arizona Custom Grips

About Magna-Tusk™ Ivory
and Stag Grips:

 Magna-Tusk™ Ivory and Stag grips, a
product of Arizona Custom Grips, are manufactured out of our
high-grade, high density ivory material designed exclusively as a premium,
high-strength grip material.  Vastly
superior to standard bonded ivory or stag found on most factory and other
aftermarket grips, Magna-Tusk™ is capable of withstanding the heaviest recoil
and impact, and is the toughest alternative grip material available today,
while still retaining the pristine look of real ivory or stag.  It is
rock-solid, stable, and water, chemical, and oil resistant.  It is
flame and heat resistant, and is entirely void-free, with over 10x the
strength, durability, and impact resistance of alternative
materials.  Unlike with real ivory or stag, there is no routine care
and maintenance involved, with no danger of it drying out and cracking if not
maintained properly or if left in the heat.  It is filled with
premium natural compounds to produce outstanding aesthetic properties and
mechanical performance.  When aged with our natural aging process, it
takes on the equivalent of a 100-year-old patina, with subtle grain details
which many experts cannot tell apart from the real thing.  In
addition, the material has a fine grain structure, which holds intricate detail
for carvings, artistic relief work, etc., found on many historic grips.  

08292000

Please note that the photo used is a stock photo (a
sample pair).  Yours will appear similar to these. 

Customer
satisfaction is important to us – we guarantee your complete satisfaction with
every purchase!!